MADE IN ITALYlanguageENGINE DRIVEN WELDERTS 200 BS/EL | BS/EL P4 STROKE, OHV, NATURAL ASPIRATEDModelHONDA - GX 390* Stand-By net power8.2 kWm (11.1 hp)* PRP net power6.4 kWm (8.7 hp )* COP net power/Cylinders / Displacement1 / 389 cm³ (0.39 lt.)Bore / Stroke88 / 64 (mm)Compression ratio8.2 : 1BMEP (Brake Mean Effective Pressure : LTP - PRP)/Speed governor type MechanicalFUEL CONSUMPTION110 % (Stand-by power)3.5 lt./h100 % to PRP 3.2 lt./h75 % to PRP 2.4 lt./h50 % to PRP 1.6 lt./hCOOLING SYSTEMAriaTotal system cap. - only engine /Fan air flow/LUBRICATION SYSTEMTotal oil system capacity/Oil capacity in sump1.1 lt.Oil consumption at full load/EXHAUST SYSTEMMaximum exhaust gas flow/Max. exhaust gas temp./Maximum back pressure/External diameter exhaust pipe/ELECTRICAL SYSTEM/Starter motor power/Battery charging alternator cap./Cold start/With cold start aid/AIR FILTERDryCombustion air flow/HEAT REJECTED AT FULL LOADTo exhaust system/To water and oil/Radiated to room/To charge cooler/EnginE 3000 rpm* Output powers according to ISO 3046-1aircooledpetrolmanualrecoilThe images are for referenceWELDING PROCESSShielded Metal Arc welding SMAW (STICK)FEATURES•Arc welding source in D.C. welding•Welds any type of electrode, including cellulosic•The steel stretcher provides protection for the entire machine•A.C. generator, single-phase and three-phase•Aux power also available while welding•Ground fault interruptor•Engine shut-down (oil alert)•Meets EC directivespag 112/2020DEFINITIONSSMAW: Coated electrode welding is an arc welding with protected metal.GMAW: welding is an arc process with metal under gas protection.FCAW (FLUX CORED): The process with cored wires is very similar to MIG / MAG welding. Continuous wire is not full but consists in a metal strip that wraps a powders core (flow).GTAW: is a welding process that uses a tungsten electrode that cannot melt.ENGINESTAGE5
MADE IN ITALYlanguageWELDING AND GENERATIONTS 200 BS/EL PASYNCRONOUS THREE-PHASE, SELF-EXCITED, BRUSHLESSInsulation classHa.C. gEnErationC.C. WEldingCOSTANT CURRENTTS 200 BS/ELTS 200 BS/EL PCurrent range20 ÷ 155A20 ÷ 170AType of regulationcontinueDuty cycle155 A - 60% | 120 A - 100%170 A - 60% | 140 A - 100%Open circuit voltage65 VArc Force RegulationNogEnEral SpECifiCationSFuel tank capacity6.1 lStarter Battery2 l/hFuel consumption (welding 60%)3 hRunning time (welding 60%)/IP protection degreeIP 23Acoustic power LwA (pressure LpA)98 dB(A) (73 dB(A) @ 7 m)gEnErazionE auSiliariaOUTPUT 1TS 200 BS/ELTS 200 BS/EL PType of source Three-phaseFrequency50 HzApparent Power (Active Power)6 kVA (4.8 kW)Cos j/Voltage400VCurrent8.7 AOUTPUT 3TS 200 BS/ELTS 200 BS/EL PType of source Single-phase/Frequency50 Hz/Apparent Power (Active Power)2 kVA (1.6 kW)/Cos j//Voltage48V/Current41.6 A/OUTPUT 2TS 200 BS/ELTS 200 BS/EL PType of source Single-phaseFrequency50 HzApparent Power (Active Power)4 kVA (3.2 kW)Cos j/Voltage230VCurrent17.4 AOUTPUT 4TS 200 BS/ELTS 200 BS/EL PType of source Single-phaseFrequency50 HzApparent Power (Active Power)2 kVA (1.6 kW)Cos j0.8Voltage110V (CTE)Current18.2 AThe use of the Auxiliary Generation is recommended for tools related to welding (wheels, electric hammers, lights, etc ...)pag 212/2020